Видео

oh mine, all my figures still intact, nothing missing

Did you silicone corners first?

Pretty sure you should make two types.... One with stickiness for horizontal and one for verical... getting a 2 inch thick barrier and stacking it up multiple times really looks idiotic, and the stack will look uneven.

I have a large mirror that is glued all to heck to the wall. I was just going to use duct tape, break up the mirror and pick up the pieces. I didn’t think about using carpet shield, and we happen to have a whole new roll already. Thanks for video.

NICE

I have tried floor model AC with the vent running out a hole created for the vent and it didn't seem to cool it at all after all day. I also have tried window AC 12k and vented out the canvas. Nothing has worked and I've tried in two pop ups. Help

What do u do when it just keeps spinning and won't unscrew

Thank you for showing us how to remove mirrors safely.

Thanks to your video we were able to remove our mirror safely. Greetings from Belgium 💪

Mine cracked overnight for no reason. It was fine an hour ago and now not so much

Where do I get that adhesive plastic?

I had two bath mirrors to remove. I tried your method on the first mirror and was left with tiny shards of glass everywhere. The second mirror I used the wood shim method. The shims worked great and left no broken glass, and no mess to clean up. My recommendation is to stick with the shim method. It's safer and less clean up.

Used this to remove 3 walls of mirror! This works well.

Link to AC installation video - ruclips.net/video/_j01LJAM1Aw/видео.htmlsi=jL6eUkxy30e2tq8R

a.co/d/dJbgOjR link to insulation product

Thank you for doing this video. I'm about to do the same in a box truck although I am going to vent the hot air out the side with a vent. Was trying to figure out how to get air to the sides and top of the ac unit? So it looks like you're using the air inside the cabinet and the air inside the camper for that purpose? or am I seeing it wrong? I like the idea sometimes video creators follow the crowd and over engineer a project. Not going to be living in it just need it cool when traveling (especially sw Fl) How is that working out?

id you add refective to the roof over the ends or a tarp you will see a big change

You saved my life!!! Had to take down five 5’ x 8’ and this worked great……super great idea 👍

I’m not planning on smashing my tiles with a hammer so I feel like both could work

Best method ive seen 👍

Did you get 7 years of bad luck?

Continuing the reply from below, the mirror did come off stuck to the shield. I would probably add to your post that maybe break a smaller section at a time cutting the shield and removing as you go. But it was a good idea. I am just an idiot. Thanks Phil for the idea.

Well Phil, I found your video and thought WOW! Sounds like a perfect way to remove my mirror. Got the carpet shield, put 3 layers ( must be better than 2) and picked up the hammer and tried to break the mirror. The hammer bounced off the mirror with no effect. Kept trying until it finally started breaking. I was so happy. I took my razor knife and tried to score a small section but the blade just seemed to slide along the glass and when I tried to pull that section away the entire mirror came down. Sliced my arm open, requiring 6 stitches, another piece punctured my wrist, through my glove, which caused a hematoma in my hand. But, the mirror did co

Thanks for the idea!!

how would this support the roof from falling?

Thank you! Excellent advice.

If you're getting voids, sans BB, doesn't that just mean you didn't apply enough thinset to the substrate, or provide enough pressure when setting the tile?

Thanks for the video tutorial! Just removed my monsters 7 foot width mirror a few hours ago. Helped contain the shards when bringing it down in sections. 👍

I just took my mirror out using this procedure. I used a very heavy box and taped it up good. It was a very clean removal. I did wipe up all the surfaces with wet paper towels and then hit everything with my shop vacuum just in case any little pieces of glass where on the floor. Thanks for sharing this video. It’s really the way to go.

Ive counted my fingers for just such an occasion.

Hi Phil, I hope you can read my message. I like the way that you remove the mirrors but, what kind of material you used to cover el mirrors? I'm planning to do my duty this weekend. Thank you in advance for your time and help.

my mirrors go to the ceiling, this looks like the best way I've seen to get them down. Thanks!!

Yes

Any alternative products? I’m in the UK and searched CreteBeater it’s £252 for 20 litres I only want it to clean a £10 trowel at that price I might as well throw it away and buy a new one.

Floors no need, walls highly suggest..

To all of you saying this doesn't work, you're wrong! It works, and it works great. I just did it. You have to apply some common sense when doing it. Plus, if you're not handy, don't even try it. Thank you so much for posting the video. I saved a few hundred dollars doing it myself!

I got all cut up watching this! 🫣

Sorry, but there is a MUCH better, safer way to take down a large mirror WITHOUT breaking it. Keep looking on RUclips. Our 7 mirrors each came down in one piece without breaking them.

Is it just me or did the tile come up really easily from the Ditra? I can't believe people are still doubting that tiles should be back-buttered.

But is it stain and water resistant?

You Sir, are a genius. The prep work took a little time, but it worked as advertised!

Thank You!!! really appreciate you making this video...

WOW !!! THIS IS GREAT !!! THANK YOU VERY VERY MUCH !!!!!

Nice work. .I have installed five Easy Heat systems in bathroom floors. No failures. The only thing I would do differently than you do here, is buy a longer cable so that the loops would be closer together. I don't know if you will get cool spots. An advantage of having thorough coverage of the cable is that spilled water evaporates quickly. But really, your customers have noting to worry about. This is a pro install.

We're gonna give it a try!

How to remove without breaking it. Also don't film in portrait mode.

Good to see the product doesn't sag. I will resist using this product until long term testing is done in a shower environment. Regular Prism performs horribly in a shower environment.

😮 I need my mirror.

Whenever he says back buttered drink

Love it! What a great idea!